SL70 | XL70
Parts for Honda SL70 | XL70
OEM Honda fuel petcock lever spring fits between petrol valve lever plate and the lever to apply pre..
OEM Honda fuel petcock 16mm packing fits petrol valve on many early model Hondas. Find your model nu..
Genuine Honda fuel petcock strainer screen fits petrol valve on many early model Hondas. Petock come..
OEM Honda fuel petcock strainer, bowl. 23mm fits petrol valve on many early model Hondas. Petock com..
OEM Honda fuel petcock strainer (bowl) gasket 23mm fits petrol valve on many early model Hondas. Pet..
OEM Honda fuel petcock gasket fits on top between petrol valve and the tank on many early model..
OEM Honda fuel petcock rebuild set comes with 2 rubber O-rings and 1 packing. One O-ring for the sea..
Genuine replacement SL70 and XL70 Stock Exhaust System. Made to fit the frame dimensions of the 1971..
Genuine replacement SL70 and XL70 chrome shield fits the curve of the original and replacement muffl..
Genuine hardware and packing to secure the original or replacement muffler heat shield to the S..
Genuine Honda muffler diffuser pipe fits the inside dimensions of many muffler systems in the Honda ..
OEM Honda stud 6x32. All thread.Fits models:1984-1985 ATC125M
Genuine Honda exhaust collars fit between the exhaust flange and the cylinder. Acts as spacer and pr..
Genuine replacement bracket, front fender. This part will come bare metal and needing to be sanded a..
Genuine replacement mud guard, front fender. Comes as you see it primered and needing to be sanded a..
Rear fender lower mount rubber with bracket acts as a vibration grommet.Replaces Honda Part numb..
Rear fender top mount rubber vibration grommet.Replaces Honda Part numbers:80106-118-000
Genuine replacement SL70 and XL70 side cover kit replaces the original left and right side covers an..
Genuine replacement SL70 and XL70 side cover set replaces the original left and right side covers. I..
Genuine Honda side cover grommet fits hundreds of Honda models. Mostly used to secure plastic covers..
Genuine replacement side cover grommet fits hundreds of Honda models. Mostly used to secure plastic ..
Genuine Honda side cover grommet fits hundreds of Honda models. Honda calls it a grommet, air cleane..
Genuine replacement plug for tach drive on right side crankcase cover of select Honda models. L..
Genuine Honda 22mm rubber grommet with narrow groove fits hundreds of Honda models. Mostly used to s..
Genuine Honda grommet used to protect wires passing through metal fenders and frame loops. ..
Complete package comes with our genuine replacement fork tubes, a set of fork seals, a set of Honda ..
Genuine replacement fork tubes made of the highest quality fabrication to meet or exceed OEM specifi..
Genuine Honda fork dust cover fits over the top of the fork lowers to keep dust and dirt out of the ..
Genuine replacement fork oil seal 27 x 39 x 10.5. Sold in set of 2. Use when rebuilding the front sh..
OEM Genuine Honda fork oil seal 27 x 39 x 10.5. Sold individually. You must order quantity two ..
Ball bearing #6 (3/16 in) steel. In most applications for Honda dirt bikes requires 42 pieces. Minim..
Genuine Honda thread, steering stem.Fits models:ATC110-A 1980 110 ATC110 ATV
Genuine replacement thread, steering stem with the early Honda grey bezel.Fits models:A..
Thick 6mm copper washer that seals the drain bolt on fork lowers on nearly 1000 Honda models i..
OEM Honda 13mm bright chrome washer for top fork bolt.Fits models:
OEM Honda chrome top fork bolt with O-ring oil seal. Shown from multiple angles. SOLD EACHFits m..
Genuine Honda washer, steering stem is a very thin dust seal/washer used in the steering stem assemb..
Tapered Steering Bearings with new dust seals replace loose ball bearing setup in steering stem. Dir..
OEM Honda washer sits under chrome nut, steering stem on the top fork bridge. See table below for fi..
Genuine Honda rubber washer, steering stem is a very thin dust seal/washer used on the following mod..
Genuine Honda inner bearing race for bottom of head tube.Fits models:ATC110-A 1980 110 ..
Genuine Honda inner bearing race for top of head tube.Replaces 50302-030-305, 50301-918-000..
Genuine Honda bearing race for top or bottom of head tube.Replaces 50302-030-305, 50301-918-000,..
OEM Honda chrome cap nut, steering stem. Buy this one and drill your own breather hole!Fits mode..
Genuine Honda grommet used to as vibration damping on rear fender and tail light for most of these b..
40mm snap ring fits above the fork oil seal. Will require the correct tool to remove and insert. Sol..
Genuine replacement gray switch wire sheathing designed to fit 1 to 2 wires. Sold by the foot. ..
Genuine replacement gray switch wire sheathing designed to fit 3 to 4 wires. Sold by the foot. ..
Genuine replacement front brake switch designed to fit CT70 K3 and K4. Can be used on other models b..
Genuine Honda front brake switch designed to fit models with two male bullet connectors.Part Des..
Genuine replacement SL70 chrome handlebars with NO hole drilled for horn button. 7/8 inch stock chro..
Genuine replacement SL70 chrome handlebars with horn hole drilled. 7/8 inch stock chromed. At this p..
Genuine replacement XL70 chrome handlebars. 7/8 inch stock chromed. At this price it isn't worth str..
Genuine Honda plastic throttle tube.1975-1982 CB125S
Genuine replacement SL70 and XL70 front brake cable. If you need a new brake cable for your Motospor..
Genuine replacement SL70 and XL70 3-piece cable set. If you are restoring Motosport SL70 or the..
Genuine replacement SL70 and XL70 clutch cable. If you need a new clutch cable for your Motospo..
Genuine replacement SL70 and XL70 throttle cable. If you need a new throttle cable for your Mot..
Black cable tieFits models: CT110 A (80) MOTORCYCLE, JPN, VIN# JD01-5000001 TO JD01-500..
Spring, cable adjuster found on the brake arm end of the cables to provide tension for return/r..
Replacement throttle cable for Honda models using the TB Parts 20mm and 24mm carburetors needing a l..
Aluminum cable tie with black plastic casing to secure wires to frame of many early model Honda..
OEm Honda short white cable tie approximately 5-1/16 inch long. Used on hundreds of Honda models..
OEM Honda white cable tie used on many Honda models to secure external wiring to handlebars. Approxi..
OEM Honda long white cable tie is used to secure wiring to the frame on some models. Approximately 8..
OEM Honda clip, cables. Replaces part 45465-341-700Fits models:1979-1981 ATC110
Genuine replacement SL70 and XL70 speedometer cable. If you need a new speedo cable for your Motospo..
Genuine replacement left andf right grip as found on the Honda Motosport SL series lineup from the 1..
Genuine Oury MX grip made famous back in the early days of motocross and enduro racing. Comes a..
Genuine Honda grip found on the enduro, trials and off-road models shown below. Choose left or right..
Genuine replacement clutch and brake levers for many Honda models with drum brakes front and rear. R..
Genuine replacement plastic plug used to fill the mirror tap on lever perch castings that have threa..